Martin : photos : AfM Harness Install

Here are the instructions for installing the Williams Attack from Mars pinball machine shaker motor harness.

Gallery pages: 1

< 1 of 6 >

Martin > Locate the connector for the playfield harness at the left lower side of the playfield. Run the black wire through the middle cable clip, and then down with the power harness (thickest, through the slit hose and up into the head. It might be easier to connect the black wire in the head, and then drop the harness through the hole. Screw the black wire under the grounding stud in the head

The red green and white wires go to the right side of the playfield, then up through the cable clips to the level of the target bank.

Martin > Clip the purple wire to the orange/white wire in the strobe board connector. The connector is at the bottom left of the raised playfield, and its harness runs up behind the backboard. We have switched from the telephone style connector shown to a standard squeeze style.
MAKE SURE THE WIRES ARE COMPLETELY THROUGH THE CENTER OF THE CONNECTOR AND THEN SQUEEZE WITH ROBO GRIPS TO LOCK TIGHT AND "BITE" THE WIRES. HAVE A PAPER TOWEL TO WIPE OFF ANY EXCESS THAT LEAKS FROM THE CONNECTOR AFTER TIGHTING. A credit card can be used to push the wire in the connector.

Martin > Insert the green/white/grey connectors into the target bank switch connector harness. Find this by following the switch wires to the target bank. Continue the red wire up to the right martian plastic fasher, and solder it to the red/white wire. You can use a squeeze connector if you prefer.

Martin > Here's the shaker motor, board and cabinet harnesses installed. No end caps as of yet.

Martin > Run the cabinet harness up through the cable clips, and connect it to the playfield harness.

Martin > Finally, screw the black wire under the grounding stud in the head. As noted, this might be easier done first.

Locate the connector for the playfield harness at the left lower side of the playfield. Run the black wire through the middle cable clip, and then down with the power harness (thickest, through the slit hose and up into the head. It might be easier to connect the black wire in the head, and then drop the harness through the hole. Screw the black wire under the grounding stud in the head

The red green and white wires go to the right side of the playfield, then up through the cable clips to the level of the target bank.

> Locate the connector for the playfield harness at the left lower side of the playfield. Run the black wire through the middle cable clip, and then down with the power harness (thickest, through the slit hose and up into the head. It might be easier to connect the black wire in the head, and then drop the harness through the hole. Screw the black wire under the grounding stud in the head

The red green and white wires go to the right side of the playfield, then up through the cable clips to the level of the target bank.

Locate the connector for the playfield harness at the left lower side of the playfield. Run the black wire through the middle cable clip, and then down with the power harness (thickest, through the slit hose and up into the head. It might be easier to connect the black wire in the head, and then drop the harness through the hole. Screw the black wire under the grounding stud in the head

The red green and white wires go to the right side of the playfield, then up through the cable clips to the level of the target bank.

Camera: Pentax Corporation (Pentax K20d ) |

More details: exif |

Original size: 4672px x 3104px |

Current: 400px x 266px |

Other sizes: Small • M • L • O • save photo |

Share photo: links, forums, blogs |

Keywords: california fremont united states eyefi

Gallery pages: 1

< 1 of 6 >

Comments

|

New comment: Requires approval

Name: Email: Link:

Connect with Facebook

Comment on: | Rating: stars

To foil spammers, enter this code:

in this box: Code unreadable?

Available Feeds | What are feeds?

Gallery Photos:

Atom |

RSS |

Google Earth